Seating Tools 91318-- [ ], 91319-- [ ], and 91320-- [ ]
408-- 4571
5. MAINTENANCE AND INSPECTION
5.1. Initial Inspection
It is recommended that the seating tool be inspected
using Figure 3 immediately upon arrival in your facility
to ensure that it has not been damaged during
shipment.
A
B
C
5.2. Daily Maintenance
It is recommended that each operator be made aware
of, and responsible for, the following steps of daily
maintenance:
1. Remove dust, moisture, and other contaminants
with a clean, soft brush, or lint--free cloth. Do NOT
use objects that could damage the tool or any of its
components.
2. Ensure that the screws are in place and
secured.
SEATING TOOL
91318--1
91318--2
91318--3
91319--1
91319--2
91319--3
A
23.88 [.940]
47.75 [1.88]
95.50 [3.76]
24.89 [.980]
49.78 [1.96]
149.35[5.88]
DIMENSION
B
44.45 [1.75]
38.10 [1.50]
C
26.97 [1.062]
25.40 [1.00]
3. When the tool is not in use, store it in a clean,
dry area.
5.3. Periodic Inspection
Regular inspections should be performed by quality
control personnel. A record of scheduled inspections
should remain with the tool or be supplied to
supervisory personnel responsible for the tool. The
inspection frequency should be based on the amount
of use, working conditions, operator training and skill,
and established company standards.
91320--1 24.89 [.980]
91320--2 49.78 [1.96] 28.70 [1.13]
91320--3 248.92 [9.80]
Figure 3
7. REVISION SUMMARY
Revisions to this instruction sheet include:
28.44 [1.12]
6. REPLACEMENT
The seating tool is not repairable. Order replacement
seating tools through your representative, or call
1-- 800-- 526-- 5142, or send a facsimile of your
purchase order to 1-- 717-- 986-- 7605 or write to:
CUSTOMER SERVICE (38--35)
TYCO ELECTRONICS CORPORATION
PO BOX 3608
HARRISBURG PA 17105--3608
S Updated instruction sheet to corporate
requirements
S Removed references to support anvil
S Changed Paragraph 3.2
S Replaced Step 7, added CAUTION, and added
NOTE to Section 4
S Removed phone number for customer repair
service
Rev A
Tyco Electronics Corporation
3 of 3
相关PDF资料
P51-200-G-O-P-5V-000-000 SENSOR 200PSI 7/16-20UNF 2B 1-5V
P51-100-G-O-P-5V-000-000 SENSOR 100PSI 7/16-20UNF 2B 1-5V
ASA-40.000MHZ-L-T OSC 40.000 MHZ 3.3V SMD
553-0322 LED 3MM 5V GREEN
78C06RAT SWITCH DIP RAISE SLIDE 6POS
P51-750-S-Y-P-5V-000-000 SENSOR 750PSIS 7/16 5V
P51-75-G-O-P-5V-000-000 SENSOR 75PSI 7/16-20UNF 2B 1-5V
P51-50-G-O-P-5V-000-000 SENSOR 50PSI 7/16-20UNF 2B 1-5V
相关代理商/技术参数
91319-3 功能描述:手工工具 10R RECPT SEAT TOOL RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool
913-194 制造商:SPC Multicomp 功能描述:CAPACITOR 47UF 63V
913-195 功能描述:支架与垫片 Plastic Spcr .195 in Nylon White RoHS:否 制造商:Schurter 类型:Transipillar Spacers 长度:16 m 螺纹大小:M4 外径:10 mm 材料:Nylon with Steel 电镀:Zinc
9131-9573-003 制造商:AEP 功能描述:
9131B 功能描述:DC POWER SUPPLY 30V/6A 5V/3A 制造商:b&k precision 系列:9130B 零件状态:有效 类型:工作台(AC 至 DC) 电压 - 电源:110VAC,220VAC 电压 - 输出:0 ~ 30VDC,0 ~ 30VDC,0 ~ 5VDC 电流 - 输出:0 ~ 6A,0 ~ 6A,0 ~ 3A 显示类型:VFD 字符数:- 输出数:3 大小/尺寸:17.520" 长 x 8.445" 宽 x 3.472" 高(445.00mm x 214.50mm x 88.20mm) 特性:存储器,可编程,LAN,RS232,和 USB 接口 功率(W):375W 精度 - 电压表;安培计:0.03% + 10mV;0.1% + 5mA 电压调节 - 线路:0.01% + 3mV 电压调节 - 负载:0.01% + 3mV 电流调节 - 线路:0.1% + 3mA 电流调节 - 负载:0.1% + 3mA 纹波:1mV rms 重量:33 磅(15kg) 标准包装:1
913-1MM 功能描述:支架与垫片 Plastic Spcr 1mm Nylon White RoHS:否 制造商:Schurter 类型:Transipillar Spacers 长度:16 m 螺纹大小:M4 外径:10 mm 材料:Nylon with Steel 电镀:Zinc
9131RB-K 制造商:Bud Industries Inc 功能描述:A STEEL METAL HINGE, MALE SHORT LEFT HANDED HINGE, POWDER COATED IN ROYAL BLUE (
9132 制造商:Abbatron/HH Smith 功能描述:Standoff; Hex; Brass; 2-56 Thread; 3/16" OD; 1/4" Length; Full Thread 制造商:GC Electronics 功能描述:FINE LINE SOLDER 12FT 制造商:Fluke Electronics 功能描述:LOW-MELT SOLDER 制造商:GC Electronics 功能描述:Low-Melt Solder